
Automatic Sheet Cutting – Mechanical Shearing
A brake motor and shaft-mounted reducer give quiet single or continuous strokes. Its low cutting angle keeps bowing and twist to a minimum, giving true, straight cuts of steel and non-ferrous sheet.
GCC Electro Mechanical Services W.L.L designs, supplies, installs, tests, commissions and maintains air-conditioning, ventilation, plumbing, firefighting and electrical systems for residential, commercial and industrial projects — small to high-rise.
GCC Electro Mechanical Services W.L.L is the sister company of Shams Al Nahar AC Repair & Maintenance, established in 2012. We handle the whole range of MEP projects — from small private jobs to large industrial and high-rise developments.
Our turnkey operations cover design, supply, installation, testing, commissioning and maintenance. Every stage of every project is managed by an experienced team of specialists in the required technical discipline, making sure each project is completed and handed over on time and safely.
Click any discipline to see what the work involves, the systems we build and photos from our sites.
Chilled water, DX and VRF/VRV systems designed, installed and commissioned.
Learn more →Smoke extract, jet fans, stair & lift pressurization, kitchen and toilet extract.
Learn more →Water supply, drainage, hot-water circulation, irrigation and grey water.
Learn more →Sprinklers, wet & dry risers, hydrants and fire pumps with Civil Defense approval.
Learn more →Power distribution, lighting, fire alarm, CCTV, access control and data networks.
Learn more →
In Bahrain's climate the air-conditioning system is the heart of every building. We start with heat-load calculations and system selection, then supply the equipment, install the piping, ductwork and supports, and finally test, balance and commission the whole system so every room reaches its design temperature efficiently.
Good ventilation removes heat, odours and pollutants; smoke-control systems keep stairs and lifts free of smoke during a fire so people can escape safely. We design these systems, take them through Civil Defense approval, fabricate the ductwork in our own workshop and interface them with the fire alarm system.
From the underground drainage network laid before the slab is poured, to vertical stacks in multi-storey shafts and hot-water circulation to every fixture, we deliver plumbing systems that are pressure-tested and commissioned before handover. We also work on infrastructure, irrigation and grey-water recycling.
Firefighting systems sit quietly for years and must perform instantly. We design and install them to code, obtain Civil Defense approval, and hydro-test and commission every line and pump. The red pipes you see across our site photos are sprinkler and riser mains being installed.
Electrical works start early — conduits are cast into the slab before concrete — and finish with the lights, panels and systems the client sees every day. We cover low and medium voltage power, lighting and controls, standby power, and the extra-low-voltage systems that keep a building safe and connected.
Each stage is handled by specialists in that discipline, so the project is delivered on time and safely.
Load calculations, system selection and shop drawings.
Consultant and Civil Defense submissions and approvals.
Approved equipment and materials, plus in-house fabricated ducts.
Experienced site teams with proper tools and safety.
Pressure tests, balancing and calibrated measurements.
After-handover support and fixing any complaint.
We manufacture our own galvanized and pre-insulated ductwork. Controlling fabrication means better quality, accurate sizes and faster delivery to site.

A brake motor and shaft-mounted reducer give quiet single or continuous strokes. Its low cutting angle keeps bowing and twist to a minimum, giving true, straight cuts of steel and non-ferrous sheet.

The classic machine for forming duct sections, with automatic changeover between functions so rollers no longer need to be swapped by hand.

Designed for thin sheet with one-side pre-bending; rolls sheet into round ducts and curves. Different operations by changing the folder.

Forms the Pittsburgh lock seam, S-lock and C-lock used to join rectangular ducts, on sheet from 0.5 to 1.2 mm thick.

Cuts 90° notches and elbow corners at high speed — compact and easy to operate.

Forms grooves and beads on pipes and duct parts for stiffness and joints, with 9 pairs of swaging wheels.

Specialised cutters and a fabrication table for pre-insulated panel ducts — light, airtight and thermally efficient.

Round and rectangular ducts, elbows and transitions are fabricated here and delivered ready to install.
Towers, villas, mosques, malls, restaurants, hotels, warehouses and government facilities across Bahrain.
Click any photo to enlarge.
The right equipment for fabrication, installation and accurate testing & commissioning.
Tell us about your building and the systems you need — we'll get back to you with a proposal.